Medical Infrared Thermometer Non Contact Celsius / Fahrenheit Mode
Selectable
Instructions
1) Power on
2) Point the infrared detector part to the center of the
forehead—above the center of the eyebrow and keep it
vertical. The measurement area must not be covered by hair. If
there is sweat, it should be dried.
3) The body temperature is displayed on the screen, the value is
recorded, and the temperature measurement is
completed.
Parameter
Measurement range (ET305): -50 ° C to 1050 ° C (-58 ° F to 1992 °
F).
Spectrum range: 8 to 14 um.
Infrared temperature measurement accuracy: ± 1.8% or 1.8 ° C (4 °
F).
T-C temperature measurement accuracy: ± 1% or 1 ° C (2 ° F)
(assuming that the ambient operating temperature is
23 to 25 ° C (73 to 77 ° F) below 0 ° C original base + 1 ° C,
below -35 ° C is for reference only).
Repeatability: ± 0.5 ℃ or ± 0.5% of reading.
Response time (95% S): 250 ms.
ET305 optical resolution (D: S): 50: 1.
Emissivity adjustment: 0.10 ～ 1.00.
Display resolution: 0.1 ° C (0.1 ° F) (0.2 ° C below 10 ° C; 1 ° C
/ 1 ° F above 999.9).
Secondary display information: maximum, minimum, difference,
average.
laser:
Aiming: single point laser;
Power: Class 2 (II) operation; output <1 mW, wavelength 630 to
670nm.
Electrical indicators:
Power: 6F22 9V battery;
Power consumption: about 30 hours battery life (alkaline), about 10
hours battery life (carbonity).
Precautions:
1. Please read the instructions carefully before measuring, and the
forehead should be kept dry and the hair should
not cover the forehead. (Please measure in the environment of 10 ℃
-40 ℃) to ensure the accuracy of the
measurement.
2. The forehead temperature quickly measured by this product is for
reference only and should not be used as a
basis for medical judgment. If abnormal temperature is found,
please use a medical thermometer for further
measurement.
3. Please protect the sensor lens and clean it in time. If the
temperature change during use is too large, it is
necessary to place the measuring device in the environment to be
measured for 20 minutes, and then use it after it
has stably adapted to the ambient temperature, and then a more
accurate value can be measured.
Note
A warning describes actions that may cause a hazardous situation to
the user. To avoid electric shock or personal
injury, follow these guidelines:
Do not aim the laser directly at your eyes or indirectly reflected
surfaces. Before using the thermometer, check
the case. If the thermometer is damaged, do not use it. Look for
damage or missing plastic parts. Replace the
battery as soon as the battery indicator "" appears. Do not use the
thermometer if it is malfunctioning. Instrument
protection may have been compromised. If in doubt, send the
thermometer for repair. Do not use the thermometer near
explosive gases, vapors or dust. To avoid the risk of burns, keep
in mind that objects with high reflectivity will
often make temperature measurements lower than the actual
temperature of the object. If this equipment is used in a
manner not specified in this manual, the protection provided by the
equipment may be impaired.
To avoid damaging the thermometer or device under test, protect
them from the following injuries:
From EMF (electromagnetic field) including electric welding
machines, electric induction heaters, static
electricity, thermal shock (caused by large or sudden ambient
temperature changes-wait 30 minutes to stabilize the
thermometer before use). Do not leave the thermometer on or near
hot objects. Various symbols and safety signs on
the thermometer and in the manual.
